features push switch option compact, low pro le high reliability metal bushing/shaft rohs compliant* pec11l series - 11 mm low pro le encoder *rohs directive 2002/95/ec jan 27, 2003 including annex. **devices are tested using standard noise reduction lters. for optimum performance, designers should use noise reduction l ters in their circuits. speci cations are subject to change without notice. customers should verify actual device performance in their speci c applications. electrical characteristics output ........................................................................................................................ ..........................................................................2-bit quadrature code closed circuit resistance ..................................................................................................... ...........................................................100 milliohms maximum contact rating ................................................................................................................ .............................................................................. 10 ma @ 5 vdc insulation resistance ......................................................................................................... ...........................................................100 megohms @ 250 vdc dielectric withstanding voltage sea level .................................................................................................................... ........................................................................... 300 vac minimum electrical travel.............................................................................................................. ....................................................................................... continuous contact bounce (60 rpm) ............................................................................................................................... ...........................................10 ms maximum** rpm (operating) ............................................................................................................... ............................................................................... 60 maximum** environmental characteristics operating temperature range ................................................................................................... ...................................-10 c to +70 c (+14 f to +158 f) storage temperature range ..................................................................................................... .................................... -40 c to +85 c (-40 f to +185 f) humidity ...................................................................................................................... ......................................... mil-std-202, method 103b, condition a vibration ..................................................................................................................... ..................................................................................................... 30 g contact bounce................................................................................................................ ............................... 10~55~10 hz / 1 min. / amplitude 1.5 mm shock ......................................................................................................................... ................................................................................................... 100 g rotational life ............................................................................................................... ..................................................................100,000 cycles minimum ip rating ..................................................................................................................... .....................................................................................................ip 40 mechanical characteristics mechanical angle .............................................................................................................. ...........................................................................360 continuous torque detent ....................................................................................................................... ........................................................20-150 gf-cm (0.27 to 2.0 oz-in) running ...................................................................................................................... .................................................. 10 to 150 gf-cm (0.14 to 2.1 oz-in) mounting...................................................................................................................... ......................................................... 70 n-cm (6.2 lb-in) maximum shaft side load (static) ............................................................................................................................... ................................. 2.04 kgf (4.5 lbs) minimum shaft strength (push-pull) .................................................................................................... ..........................................................................100 n (22.5 lbs) weight ........................................................................................................................ ..................................................................... 5 gm (0.17 oz) maximum terminals ..................................................................................................................... ........................................................... printed circuit board terminals soldering condition wave soldering........................................................................... sn95.5/ag2.8/cu0.7 solder with n o-clean ? ux: 260 c 5 c max. for 3-5 seconds hand soldering .......................................................................................................... .......................................................................not recommended hardware ...................................................................................................................... one ? at washer and one mounting nut supplied with each encoder switch characteristics switch type ................................................................................................................... ................................................ contact push on momentary spst switch life ................................................................................................................... ......................................................................20,000 cycles minimum power rating (resistive load) ................................................................................................. .................................................................... 10 ma at 5 v dc switch travel ................................................................................................................. .....................................................................................0.5 0.3 mm switch actuation force ........................................................................................................ .............................................. 610 306 gf (8.47 4.24 oz.-in.) how to order pec11l - 4 0 20 f - s 0015 model terminal con? guration 4 = pc pin horizontal/rear facing detent option 0 = no detents (15, 20 pulses) 1 = 20 detents (20 pulses) 2 = 30 detents (15 pulses) standard shaft length 15 = 15.0 mm 20 = 20.0 mm 25 = 25.0 mm shaft style f = metal flatted shaft k = metal knurled shaft switch con? guration s = push momentary switch n = no switch resolution 0015 = 15 pulses per 360 rotation 0020 = 20 pulses per 360 rotation *rohs compliant
12.8 (.504) 11.8 (.465) 13.6 (.535) f l ?0.5 (l ?.020) 0.75 (.030) m7xp 3 plcs. 0.5 (.020) c 1.0 +0.2/-0 (.039 +.008/-0) dia. 3 plcs. 1.4 (.055) 2.1 (.083) 2.0 (.079) 7.5 (.295) 6.0 (.236) 6.0 (.236) 7.5 (.295) 4.5 (.177) 6.0 +0/-0.1 (.236 +0/-.004) dia. 5.0 (.197) 5.0 (.197) b b b 4.5 (.177) dia. l a c p 18 teeth knurled 1.0 (.039) 6.0 +0/-0.1 (.236 +0/-.004) ac b 12.8 (.504) 11.8 (.465) 5.0 (.197) 13.6 (.535) f l ?0.5 (l ?.020) 0.75 (.030) m7xp switch travel 0.5 +0.4/-0.3 (.020 +.016/-.012) 1.0 +0.2/-0 (.039 +.008/-0) dia. 5 plcs. 1.4 (.055) 2.1 (.083) sw a 12 cb 2.0 (.079) 7.5 (.295) 7.0 (.276) 6.0 (.236) 6.0 (.236) 7.5 (.295) 7.0 (.276) 4.5 (.177) 6.0 +0/-0.1 (.236 +0/-.004) dia. 5.0 (.197) 5.0 (.197) 3.7 (.146) 3.7 (.146) 4.5 (.177) pec11l-4xxxf-sxxxx pec11l-4xxxf-nxxxx 3.7 (.146) 0.8 (.031) 13.6 (.535) rev. 02/11 speci cations are subject to change without notice. customers should verify actual device performance in their speci c applications. pec11l series - 11 mm low pro le encoder product dimensions dimensions: mm (inches) lbfpac 15 (.591) 5.0 (.197) 7.0 (.276) 7.0 (.276) 6.0 (.236) 7.0 (.276) 20 (.787) 7.0 (.276) 10.0 (.394) 7.0 (.276) 6.0 (.236) 7.0 (.276) 25 (.984) 7.0 (.276) 12.0 (.472) 12.0 (.472) 10.0 (.394) 11.0 (.433) applications level control, tuning and timer settings in: audio-visual equipment consumer electric appliances environmental controls musical instrumentation communications equipment quadrature output table a signal cw d on off b signal suggested filter circuit switch circuit 12 5 vdc 10k ohms 10k ohms 10k ohms 10k ohms terminal b terminal c terminal a 0.01 f 0.01 f encoder dim. tol. <10.0 (<.394) 0.3 (.012) 10.0 ~ 100 (.394 ~ 3.937) 0.5 (.020)
|
